Reliable Factory-Made 60W Single Output DIN Rail Power Supply

1. The AC voltage specification used by the Din Rail power supply is 110VAC 220VAC 380VAC. Before powering on the power supply, check whether the connected voltage matches the power supply input voltage. 2. Do not connect the load before powering on for the first time, first check whether the output voltage of the power supply is consistent with the power supply of the connected equipment, so as not to damage the connected equipment. 3 The ground wire must be connected before the power supply is used. The ground wire of this type of power supply is at the position marked in the figure. 4. The power supply should be placed in a well-ventilated center. 5 The output current of the rail power supply is definitely determined; it is affirmed according to the rated standard current of the equipment supplied by the rail power supply or the uniform current value measured by a multimeter. When the ambient temperature is high, the air activity is not good, and the load is rational, an additional current margin of 20-30% should be prepared. 6 The input power of the rail power supply is determined: the rated input power of the rail power supply depends on the rated power of the supplied equipment. Under the condition of not knowing the rated power of the equipment supplied, it can be obtained based on the product value of the rated current and voltage of the equipment supplied (current X voltage = power). When the user selects the power supply, it should be greater than 15-30% of the practical power and peak power. 7 The number of DC output of the rail power supply is determined: the rail power supply normally has up to four outputs. (S-single group, D-double group, T-three group, Q-four group) According to the equipment provided. 8 The rail power supply has maintenance functions such as over/under voltage, over current, overheating maintenance and fan heat dissipation. Please stop the selection based on the actual application status to strengthen the stability and reliability of the system engineering. 9 The types of rail power supplies are: industrial iron shell type, rail type, LED outdoor rainproof and waterproof type, etc. Please choose according to practical application.60W Single Output DIN Rail Power Supply MDR-60 series Universal AC input/ full range Protections: Short circuit/ Over load/ Over voltage Cooling by free air convection Can be installed on DIN rail TS-35/7.5 or 15 isolation classⅡ LED indicator for power on 100% full load burn-in test 2 years warranty

Proper use of guide rail power supply

Features

Specifications

SPECIFICATIONS
OUTPUT
Model	MDR-60-5	MDR-60-12	MDR-60-24	MDR-60-48
DC Voltage	5V	12V	24V	48V
Rated Current	10A	5A	2.5A	1.25A
Current Range	0-10A	0-5A	0-2.5A	0-1.25A
Rated Power	50W	60W	60W	60W
Ripple & Noise	80mVp-p	120mVp-p	150mVp-p	200mVp-p
Voltage Tolerance	±2%	±1%	±1%	±1%
Line regulation	±1.0%	±1.0%	±1.0%	±1.0%
Load regulation	±1.0%	±1.0%	±1.0%	±1.0%
Setup, Rise Time	500ms,30ms/230VAC 200ms,30ms/115VAC at full load
Hold Up Time	50ms/230VAC 20ms/115VAC at full load
INPUT
Voltage Range	85~264VAC 47~63Hz; 120~370VDC
AC Current	1.8A/115VAC 1A/ 230VAC
Efficiency	78%	86%	88%	87%
Inrush Current	Cold start 30A/115VAC 60A/230VAC
Leakage Current	<1mA/240VAC
PROTECTION
Over Load	105%~150% rated output power
Over Load	Protection type: Constant current limiting, recovers automatically after fault condition is removed
Over Voltage	6.25-7.25V	15.6-18V	31.2-36V	57.6-64.8V
Over Voltage	Protection type: Shut down o/p voltage, re-power on to recover
ENVIRONMENT
Working Temp., Humidity	-20℃~+70℃; 20%~90% RH non-condensing
Storage Temp., Humidity	-40℃~+85℃; 10%~95%RH
Temp. Coefficient	±0.03%/℃(0~50℃)
Vibration	10~500Hz, 2G 10min./1cycle, period for 60min, each along X, Y, Z axes
SAFETY
Withstand Voltage	I/P-O/P: 3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC
Isolation Resistance	I/P-O/P, I/P-FG, O/P-F/G: >100M Ohms / 500VDC/25℃/70% RH
STANDARD
Safety Standard	Design refer to UL508, UL60950-1,TUV EN60950-1,EN50178
EMC Standard	Design refer to EN55011,EN55022,EN61000-3-2,-3,EN61000-4-2,3,4,5,6,8,11,EN55024,EN61000-6-2，EN61204-3, heavy industry level, criteria A
OTHERS
Dimension	4090100mm(WHD)
Weight	0.33Kg
Packing	42pcs/carton/14.8kg/0.82CUFT
NOTE
1.All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature. 2.Ripple & noise are measured at 20MHz of bandwidth by using a 12” twisted pair-wire terminated with a 0.1μ & 47μ parallel capacitor. 3.Tolerance: includes set up tolerance, line regulation and load regulation. 4.The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives.